A lot of people now wonder how it could be made possible. It is not very easy if you are a kind of person who is resourceful. This article aims to help you. There are instructions below you could follow on how to do it. You need all the equipment for you to start. Otherwise you cannot start doing them without the necessary stuff you need.
If everything is ready already, then write down all the instructions on the paper. So you will not forget what you would do next. This is very important for beginners. And someone who have not tried it before. Doing the reflow soldering oven is not that difficult. And with the simple steps that are given below, to make it easy for you. Just follow and do not create your own instructions so it will be successful.
Prepare the thermometer together with the timer. You will be using them once you plug them in to the switch. You can use the one that is found on the oven but best you will have something that you would use outside.To carry them around with you. And check the temperature.
Start making your motherboard. This is your platform. And all your plans will be based on here. You should lay it down and then see if it is complete already and ready for use. And put some markers to it. For easy identification.
Add flux. The purpose of putting one for easy modification. And can be used as marker too. Apply it to the balls. So they will be protected. And to avoid them from keep moving around the board. It is very important that they must stay in their specific location.
Then align all the components inside. Lay them down on the flat surface. Most will use a silk screen for easy viewing of the different activities. Watch them they are slowly melt and changes its present state. Best that you will not leave them. So you could monitor.
Start them cooking. Just ensure they fit inside. After you put them inside. Close the door of the toaster. You can now cook them for 20 minutes. Just use the timer and thermometer from outside so it will be easy for you. No need to use the temperature of your oven. And see the changes from outside. Do not leave them. You have to watch them until it is done. And make sure to turn them off right away after use.
Let them cool. If it is done, turn them off right away. The best and only way to cool them down is to open the door. Never touch anything nor move them around. It will not take long and check if the temperature drops to 50 degrees Celsius. Then you are assured that they are cold already. That is you way to see if they are okay already. If you think they are still hot enough, then leave them and come back when it is okay.
Check them after. You have to check after. This is necessary that all components are still present. And you have achieved what you wanted. When all have been connected then, it is a sign that you are successful.
If everything is ready already, then write down all the instructions on the paper. So you will not forget what you would do next. This is very important for beginners. And someone who have not tried it before. Doing the reflow soldering oven is not that difficult. And with the simple steps that are given below, to make it easy for you. Just follow and do not create your own instructions so it will be successful.
Prepare the thermometer together with the timer. You will be using them once you plug them in to the switch. You can use the one that is found on the oven but best you will have something that you would use outside.To carry them around with you. And check the temperature.
Start making your motherboard. This is your platform. And all your plans will be based on here. You should lay it down and then see if it is complete already and ready for use. And put some markers to it. For easy identification.
Add flux. The purpose of putting one for easy modification. And can be used as marker too. Apply it to the balls. So they will be protected. And to avoid them from keep moving around the board. It is very important that they must stay in their specific location.
Then align all the components inside. Lay them down on the flat surface. Most will use a silk screen for easy viewing of the different activities. Watch them they are slowly melt and changes its present state. Best that you will not leave them. So you could monitor.
Start them cooking. Just ensure they fit inside. After you put them inside. Close the door of the toaster. You can now cook them for 20 minutes. Just use the timer and thermometer from outside so it will be easy for you. No need to use the temperature of your oven. And see the changes from outside. Do not leave them. You have to watch them until it is done. And make sure to turn them off right away after use.
Let them cool. If it is done, turn them off right away. The best and only way to cool them down is to open the door. Never touch anything nor move them around. It will not take long and check if the temperature drops to 50 degrees Celsius. Then you are assured that they are cold already. That is you way to see if they are okay already. If you think they are still hot enough, then leave them and come back when it is okay.
Check them after. You have to check after. This is necessary that all components are still present. And you have achieved what you wanted. When all have been connected then, it is a sign that you are successful.
About the Author:
When you are searching for the facts about a reflow soldering oven, go to our website today. More details can be seen at http://www.sikama.com now.
0 التعليقات:
Post a Comment